Manuals & Downloads Index
LightBurn Material Test
Preface We recommend using LightBurn's material testing feature before engraving or cutting new materials to determine the optimal parameter. At the same time, we have tested some common materials and the following are the recommended parameters for ...
Material Library for Fiber and CO2 Laser
Located below you will find our machines and their associated library. Click the link to download for your machine. Thunder CO2 glass tube parameter library Thunder CO2 RF tube parameter library Thunder Fiber laser tube parameter library Laser safe ...
Files transfer failed when sending files
Problem description The laser software shows "File transfer failed" or "Communication Error" when we send the file to the machine. In LightBurn: In RDWorks: If always get a communication error but no other errors, it might be the machine and software ...
Communication Error
Problem description A "Communication Error" occurs when sending the file to the machine. Which means the machine and software are not connected successfully. In LightBurn: In Lightburn, it will show "File transfer failed". In RDWorks: Reasons 1. The ...
Schematic of all machine iterations of the Thunder
How to delete the memory of the controller
Why we need to delete the memory It will cause a file transfer error if the memory file is full. When the software prompts the following warning, you need to clean up the files in memory. LightBurn: RDWorks: Here is a link to a video for ...
Warranty Certificate--Nova, Nova Plus, Titan, AURORA,Thunder Bolt Series
Warranty Certificate : 2026 Nova Nova Plus Titan Thunder Bolt Aurora Nova Nova Plus Titan Thunder Bolt Aurora 2025 Nova Nova Plus Titan Thunder Bolt Aurora Nova Nova Plus Titan Thunder Bolt Aurora End.
How to use EZCAD
How to use EZCAD Code Bar
How to use EzCad2 Hatch
How to install and calibrate the lightburn camera
Lightburn-Scan offset testing
You can download the file for adjust Scan Offset setting.
Lightburn software download site
Lightburn software download site:https://lightburnsoftware.com/
How to upgrade the firmware
Note: The firmware must be provided by Thunderlaser. Please make sure the software and laser machine are connected before updating. Step1: Step2: Step3: Step4: Choose the firmware we provide. After this step, the software will show that “ Update ...
Laser cutter has a wrong cutting/engraving size
Reason: Wrong pulse setting of X/Y axis motors Solution: 1. Please draw a 100x100mm square using the cut mode and send to your laser cutter and cut the square. 2. Let’s say the actual size of the square measured is 98x95mm 3. In RDWorks, go File(F)>> ...
Wrong proportions from RDWorks
Reason: "Enable rotate engrave" is enabled. I’d like to cut a Rectangle at 30x30mm, however, it become 30×60.2 in simulation and in laser. Solution: Please make sure “Enable rotate engrave” is not ticked. End
How to import PDF files into RDWorks
1. RDWorks cannot read PDF and open it directly. 2. Use CorelDraw to open/import PDF file firstly. Then save the graphic as DXF file. Like below: 3. Then RDWorks can read the DXF file, Just import the DXF file into RDWorks directly. 4. The ...
Why does the graphic size that imported to RDWorks different from its original size
Reason: If the file being imported is DXF format, the problem maybe the original file and RDWorks have different units. For example, the unit of the original DXF file is “inch”, but in RDWorks, the DXF unit is set as “mm”. When you import the DXF ...
How to setup wireless network connection for Thunderlaser machine
Here's what you'll need: A computer with wireless capability A wireless router An Ethernet cable A Thunder laser system Step: 1. router setup Use the Ethernet cable to connect the wireless router to the Ethernet port on your laser system. Connect the ...
How to run several laser machines with one PC via USB cable connection
If there are several USB interfaces with your PC, it’s able for one PC (laser software) to connect with several machines. pc to hub , one port of the hub goes to laser But For USB connection as below, 1. Pc to hub , one port of the hub goes to laser. ...
How to run several laser machine with one PC via Ethernet cable-RDWorks
If there is an Ethernet hub in your network, it’s able for one PC (laser software) to connect with several machines. But pc will does only communicate with one machine and sending the file into the laser in the same time. 1. Ethernet hub setup PC to ...
Why USB connection is not working-RDWorks
Reasons: 1. USB cable is loose or faulty Solution: Unplug the USB cable and plug it back, try again. If re-plug the cable, problem still exists. 2. USB driver is not install successfully Before you install the software, please install the USB driver ...
RDWorks-Scan offset testing
You can download this file to test and adjust the Scan Offset settings.
RDWorks plug-in installation instructions
RDWorks plug-in installation instructions