Accessories & Peripherals
Chuck Rotary Setup and Usage in Lightburn (Nova/Odin)
Chuck Rotary Setup and Usage in Lightburn (Nova/Odin) The following article, supported videos and images will guide you to success with your Thunder Chuck Rotary. NOTE* There are a few style Chuck rotary available through Thunder Laser, Please check ...
HF-75S 3 Inch 27 CFM MIXED FLOW INLINE FAN
Venting The Exhaust From Your Thunder Laser
Preface: This article covers some key points about Venting Your Laser and adapting aftermarket exhaust components Important Considerations: Existing Systems Do not connect the exhaust output of this laser to an existing exhaust system. Please consult ...
How to Use Roller Rotary on Your Machine
Preface This guide provides step-by-step instructions for setting up and operating the roller rotary attachment, which is compatible with all Thunder Laser models. The configuration shown uses the Thunder Bolt as an example. It covers basic ...
How to Install and Use the RDV Print Driver
Preface RDVPrint is a print driver software which help you using laser machine as a printer. You can draw anything in the software you like or are familiar with, such as CorelDRAW, Adobe Illustrator and Photoshop, even Microsoft Word, then"print" to ...
Instruction Exhaust Fan Manuals For THUNDER LASER
Simple information about the Exhaust Fan on the THUNDER LASER machine. Machine Series Model of Machine Model of Exhaust Fan Diameter of Exhaust Duct NOVA Series NOVA24 & 35 Ver 2.0 / Ver 2.5 / Plus HF-150PE 150mm NOVA51 & 63 Ver 2.0 / Ver 2.5 / Plus ...
Installation and Usage of CCD Camera
Installation: Usage: Software: Please download it from our official website. Downloads | THUNDER LASER The unzip password is 123456. Driver: Please refer to this link article.How to install CCD camera driver manually Still need help? For specific ...
How to install CCD camera driver manually
Problem: If the SV300 model has been selected during the installation of RDWorks and the installation of the driver has been completed, it is still not possible to connect to the CCD camera. Even when using the computer's own webcam, the presence of ...
How to adjust the air pressure value of the air pressure detector
The air pressure detector is used to adjust the air pressure value. End.
Antifreeze liquid added
Antifreeze Brand The brand we suggest is CLARANT. Website is https://www.clariant.com/en/Corporate/Search?q=Antifrogen-N The two models are suitable for laser products. 1. Antifrogen N Antifrogen® N is a liquid, tinted pale yellow, for use as a heat ...
Laser water coolants & additives
Overview There has been much debate, experimentation, and documentation on the subject of water cooled lasers with regards to the main cooling fluid and additive combinations. The theoretical, as well as practical, implementations and observations ...
Dual-stage Air Assist Sequencing issues
1. Problem description: The machines are equipped with dual air assist have an issue: Set High blow for job and run the job from software, the air assist on the machine is Low assist channel on. But if you run it from machine, it's normal. 2. ...
Thunder Laser Dual-Stage Air Assist sequencing issues
Thunder Lasers with dual-stage air assist systems sometimes experience sequencing issues. This anomaly is predominately occurring when the laser is connected to the PC via USB. If you toggle air assist ON in LightBurn the high volume stage should ...
Selecting between low and high Dual Air Assist stages in LightBurn
Selecting Between Low and High Dual Air Assist Stages In LightBurn If yours is working backwards please see this article: Thunder Laser Dual-Stage Air Assist Sequencing Issues
Retrofitting Dual Air Assist
for Thunder Laser Nova series machines with single air-assist. This is an advanced level installation. Here are all of the resources we have on this: Please see attachment Additional resources: Dual Air Assist Theory of Operation and Schematics How ...
Dual Air Assist Theory of operation and schematics
This is a typical installation of the dual stage air-assist in the Nova series machines. Your configuration may differ slightly. The maximum recommended operating system pressure, according to Thunder China Engineering, is now 40 psi to help prevent ...
How to use an air compressor
Dual air assist system instructions for use
Video:
Manuals of SRA-500XL
Manuals of SRA-500XL
How to replace the filter of SRA-500XL
How to judge if the pre-filter need to be replace When the numbers of digital screen>50%, the yellow light will turns on. It shows that the extraction power not strong, the filter cloth and the pre-filter need to be replaced. Replace instruction 1. ...
Cleaning your stock exhaust fan
This is what can build up in your exhaust system, especially the fan, and can cause critical failure so its important to regularly maintain your exhaust system. Here is how to clean the HF-150 Inline Fan that ships with the Mini 60 and Nova 24: Here ...
Exhaust fan cannot extract smoke or dust
Reasons: 1. Exhaust fan break down Solution: there’s a common way to connect it to the power directly using the power cable of chiller, then check if exhaust fan can be turn on normally. See below. 2. Connect the fan inlet and outlet in opposite ...
ThunderCAMs vs.LightBurn&Other USB Webcams
There is a lot of information (and misinformation) floating around about LightBurn's camera feature as they relate to Thunder Laser machines. There are also a lot of questions about what camera works with what laser. We are going to aggregate the ...
ThunderCAM Installation - Lightburn camera
NOTE: its a good idea to tape it up first and view it before you stick it down. The mounts are 3d printed and the adhesive is strong. Removal would likely break it. If you happen to get it upside down (many do) that's no big deal, just take out the ...