How to Replace a Nova Z Axis belt
Preface: This article is basically a copy paste of the attached PDF that covers how to replace the Z axis belt on your Nova series laser. It is currently a work in progress.
This work should be performed with the machine powered off and unplugged. Perform this work at your own risk.
Before you start to do this, please keep all screws or parts after you remove them. This is a fairly lengthy install process, so allot the proper amount of time to get it done.
Tools You will need:
12mm Gauge Block
Metric Allen Wrench Set - 3mm and 4mm
Calipers
Snap Ring Removal Tool (Was included in toolbox)
Sharpie
Camera
Knife/Heavy Duty Scissors
Prework:
-Remove front Lower Machine Door
-Remove the honeycomb Bed and Knives
-Remove the Crumb Tray(s) (Good time to dump and clean)
-Remove the Belt Covers (If applicable)
-Mark the position of the tensioners and screw rod mounting brackets with the Sharpie
-Take pictures of the belt routing with your camera
Belt Removal:
Since the belt is in need of replacement, the easiest removal method would be to cut belt and remove it. This will eliminate the belt tension on the tensioner pulleys and ease the removal of the tension blocks in preparation of the belt replacement.
With the belt removed:
1. Remove 3 tensioners and then use the snap ring pliers to remove the snap ring to release the bearing and pulley from the tensioner bracket
Left Side Tensioners | Right Side Tensioner |
Snap Ring and Bearing Removed | Components removed from Tensioner Bracket |
Example video of using snap ring pliers with snap rings. Or you can use needle-nose pliers to remove it.
2. Remove the Knife Support Bar from the front and rear Screw Rods
3. Unbolt the 4 screw rod plates (upper and lower mounting brackets).
4. Loosen the bolts for the Z Bed Honeycomb Motor
Installation:
1. Remove 4 Screws Rod from Machine
2. Place belt in the machine and spread it out.
3. Place 4 Screw Rods Back into machine with the belt on the outside of the pulleys. Screw into place but not tight.
4. Install tensioners back onto belt, re-insert the Snap Ring to hold the tensioner pulley in each tension block. Pay attention to the orientation of the belt and that the tensioner contacts the smooth side of the belt.
5. Thread the new belt around the Z motor. Tighten the Z motor down to the base.
6. Reinstall the screw rod mounting bases (do not fully tighten the bolts). Find a piece of wood or aluminum block, the thickness should be 12mm.Then put the aluminum block to the inside of the bar.
See below picture.
Note: All 4 screw rods must be calibrated with this aluminum block.
7. Tighten the bolts the fours screw rods, for the two screw rods at the front side. When you tighten the blue mounting blocks, be sure to measure the distance between the block and machine housing as shown.
The distance of the bottom side is 111mm.
The distance of the up side is 105mm.
Note: 0.5-2mm error is acceptable.
8. Put the belt inside the three blue tension bases and reinstall the tensioner pulleys. Then tighten the one on the right. You do not have to make it the belt super snug, we will be adjusting the Z bed later on and will need to remove tension to do so.
9. Rotate the gear of the screw rod to rise up the sliver holder, other corners also need to be raised up.
10. Put the knife holder on and tight it slightly. Make sure it’s level and then tight it.
11. Find a cube (the cube shown is 45mm), and put it to four corners for measure the distance between the knife holder is the same. If the distance of which corner is different, please rotate the gear of the screw rod to adjust. Move the laser head to each of the four corners and repeat these steps until the distance is the same.
12. Put two knifes on the knife holder, one put the left side, the other put the right side. Make sure there has a little space between the knife and the knife holder (about 2-3mm.)
13. Tight the screws of knifes holder.
14. Tighten the blue tensioner on the right side and one of two blue tensioners on the left side slightly.
15. Pull the belt from right side to left side, then fix the last blue tensioners.
Please note: Do not rotate the gear of the screws rod during this process. If the gear is rotated, you will need to adjust bed level again.
16. Tight all blue tensioners and check the tension of belt. It should be snug but not banjo tight.
END.
Related Articles
How do I replace the X-axis belt
X-axis belt replacement and adjustment Tools needed M3 Screwdriver Plier 5.5mm wrench New belt A pair of scissors Masking tape Disassemble Turn off the machine and unplug the power cord. Remove the upper front door with keys that came with the ...How do I replace the Y-axis belt
Y-axis belt replacement and adjustment(Take the right side of the Y axis belt as an example) Tools needed M3 Screwdriver Plier 5.5mm wrench New belt A pair of scissors Masking tape Disassemble Turn off the machine and unplug the power cord. Remove ...How to replace the Z-axis lead screw on the Thunder Bolt
Tools needed： 1. Allen wrench set × 1 set 2. Steel ruler × 1 pcs 3. Lead screw × 1 pcs 4. Open-end wrench M5 * M8 × 1 pcs 5. Marker × 1 pcs 6. Positioning fixture × 1 pcs Note: A three-dimensional triangular wooden block is used to secure the lead ...Nova Series User's Manual
Please see attached: ENDHow to replace the rollers and adjust the X axis shaft?
Replace the rollers: Adjustment of X-axis shaft 1.Please check before adjustment ①Hold and shake it to check if it becomes loose.(can’t be wobble obviously) ②In the back of X Axis Shaft have four rollers, both of them should locate on the rail.(can ...