How to Handle a MAX Fiber Laser Back-Reflection Lockout

How to Handle a MAX Fiber Laser Back-Reflection Lockout

1. What Is a Back-Reflection Lockout?

If the machine stops producing laser output and a complete restart does not restore operation, the MAX fiber laser source may have entered a protective lockout.

Back reflection occurs when part of the laser energy is reflected from the workpiece or cutting head back toward the laser source. This is more likely when cutting highly reflective materials, particularly brass, copper, and aluminum.

During process-parameter testing, we have occasionally encountered this condition, most commonly while cutting brass. When excessive back reflection is detected, the laser source first disables emission to protect its internal optical components.

The NcStudio cutting software may not display a detailed alarm. The machine may continue moving normally, but no laser is emitted. The specific alarm must therefore be checked in the MAX laser monitoring software.

In some cases, restarting the machine restores operation. However, repeated alarms may trigger a protective lockout. On the current configuration, this may occur after approximately three alarm events within one day, although the exact protection logic may vary depending on the laser model and firmware version.

A protective lockout is intended to prevent permanent damage to the pump source, internal optical path, output fiber, QBH connector, and cutting-head optics.

2. What to Check After the First Alarm

Do not simply restart the machine and continue cutting without checking the cause.

When the first back-reflection alarm or unexplained loss of laser output occurs:

1.  Stop the cutting process.

2.  Inspect the protective window for dust, oil, metal spatter, burn marks, scratches, or coating damage.

3.  Clean or replace the protective window as required.

4.  Check that the nozzle is undamaged and correctly centered.

5.  Verify the nozzle height and cut focus.

6.  Confirm that the piercing and cutting parameters are suitable for the material and thickness.

7.  Check whether the material has been fully pierced and cut through.

8.  Verify the assist-gas type and pressure.

9.  Open the MAX monitoring software and save screenshots of the active alarm and log information.

A contaminated protective window may increase reflection or refraction inside the optical path. Incorrect parameters may also prevent the laser from fully penetrating the material, resulting in increased reflected energy.

If the same alarm occurs repeatedly, stop processing immediately. Repeatedly restarting and testing the laser may convert a recoverable alarm into a protective lockout.

3. How to Confirm That the Laser Source Is Locked

The laser source may be locked if all of the following apply:

● The machine moves normally but does not emit laser.

● Restarting the machine does not restore laser output.

● The NcStudio software does not show a clear alarm.

● The MAX monitoring software shows a back-reflection, optical, or lock-related alarm.

● The Locked indicator remains active.

Before requesting an unlock, correct the condition that caused the alarm. Unlocking the laser without correcting the root cause may result in another immediate alarm or lockout.

4. Unlocking Procedure

Step 1: Capture the Required Information

Open the MAX laser monitoring software and take clear screenshots showing:

● The lockout or alarm reason.

● The laser-source serial number.

● The complete Monitor (Laser) page.

● The Decryption page, if applicable.

● The relevant entries on the Log page.

Send these screenshots to your local Thunder Laser support team.

Example Image 1: Alarm and Serial Number Information

The software icon, page layout, and menu names may vary depending on the MAX monitoring-software version.


Step 2: Request Temporary Decryption Credentials

The local support team will submit the information to MAX Technical Support.

After reviewing the alarm and confirming the laser serial number, MAX may generate temporary decryption credentials or an unlock code specifically for that laser source.

The temporary credentials are normally valid for 72 hours from the time they are generated.

If the credentials are not entered and the laser is not unlocked within 72 hours, they will expire. A new request must then be submitted.

Each set of credentials is assigned to one laser source according to its serial number. Credentials generated for one laser cannot be used with another laser.

Step 3: Enter the Credentials in the MAX Monitoring Software

Enter the temporary account, password, or unlock code on the Setting(Laser) page of the MAX monitoring software.

Example Image 2: Entering the Temporary Decryption Credentials

Do not guess or repeatedly enter the credentials, as multiple incorrect attempts may trigger an additional lockout. Passwords are case-sensitive, so carefully check all uppercase and lowercase letters.

If the “Incorrect Password” message persists, update the MAX monitoring software using the version provided by MAX or Thunder Laser Technical Support.

Before installing the new version, completely uninstall the existing version. Do not install the new version over the existing installation, as this may cause software errors or prevent connection to the laser source.

Step 4: Verify Laser Output

After the software confirms that decryption was successful:

1.  Close or minimize the MAX monitoring software as instructed.

2.  Open the NcStudio cutting software.

3.  Make sure the cutting head is positioned safely over an appropriate test material.

4.  Use the pulse function to check whether laser output has been restored.

Example Image 3: Verifying Laser Output in NcStudio

If the laser still does not emit:

1.  Return to the MAX monitoring software.

2.  Confirm whether the Locked indicator and alarm have cleared.

3.  Re-enter the same valid credentials once, if instructed by technical support.

4.  Test the pulse function again.

If the laser still does not emit, stop testing and contact technical support. Do not repeatedly pulse, restart, or enter the credentials without guidance.

5. Expected Support Time

Temporary decryption credentials must be generated by MAX according to the laser-source serial number. Thunder Laser cannot generate these credentials independently.

If the request is submitted through Thunder Laser China, please allow at least 24 hours for processing, especially when the customer and the China support team are in different time zones.

To avoid additional delays:

● Submit complete screenshots showing the alarm and serial number.

● Confirm that the protective window and cutting conditions have already been inspected.

● Use the credentials as soon as they are received.

● Do not wait until the 72-hour validity period is nearly over.

● Inform support immediately if the credentials do not work.

6. Urgent Support Through MAX WeChat

For urgent cases, MAX provides an extended-hours technical-support service through WeChat.

Scan the MAX technical-support QR code and provide the following information in the chat:

1.  Are you an equipment integrator, distributor, or end user?

2.  What is your company name and contact name?

3.  What is the laser-source serial number?

4.  Is the laser used for cutting, welding, or another application?

5.  What assistance is required?

Suggested message:

Hello. We are an equipment integrator/distributor/end user.

Company: [Company Name]

Contact: [Name]

Laser S/N: [Serial Number]

Application: Laser cutting

Issue: The laser source has entered a back-reflection lockout. We have corrected the suspected cause and attached screenshots from the MAX monitoring software showing the alarm and serial number. Could you please help us obtain the temporary decryption credentials?

Include the complete alarm screenshot and the laser serial number. After MAX confirms that the cause has been addressed, temporary credentials may normally be provided promptly.

WeChat Support Availability

According to the current service information, the WeChat service is unavailable from approximately:

Sunday 12:30 a.m. to Monday 8:30 a.m., Beijing Time

Support is generally available during the remaining period. Service hours may change, so actual response time is subject to MAX availability.

7. Options for Overseas Customers

Some overseas customers may not have access to WeChat.

The MAX China hotline is:

400-900-9588

However, Chinese 400 service numbers are generally intended for calls within Mainland China and may not be accessible from overseas, even when +86 or 0086 is added.

Overseas customers may also try submitting a support request through the MAX website:

The availability and response time of the website form have not been confirmed. For this reason, customers should first contact their local Thunder Laser support team whenever possible.

8. How to Reduce the Risk of Another Lockout

● Inspect the protective window before cutting highly reflective materials.

● Replace any window with burn marks, contamination, scratches, or coating damage.

● Use verified process parameters for the material and thickness.

● Optimize piercing power, piercing time, cut focus, cutting speed, and gas pressure.

● Ensure that the material is fully pierced before cutting begins.

● Check nozzle condition, nozzle centering, and nozzle height.

● Stop processing immediately after the first repeated back-reflection alarm.

● Do not repeatedly restart the laser source to bypass an alarm.

● Do not continue cutting after abnormal sparks, severe piercing blowout, or failure to cut through.

● Save the alarm screenshots and logs before restarting the laser.

● Contact technical support if the cause cannot be clearly identified.

Important Reminder

Temporary decryption credentials only clear the protective lockout. They do not correct the condition that caused the lockout. The protective window, cutting parameters, material, cooling system, QBH connection, and cutting-head condition must be checked before laser output is restored.